| |
|
|
| |
| |
Cable Sealing End Caps Pvc End Caps :
|
| |
| Cable Sealing End Caps Pvc End Caps Cable End Caps Heat Shrink End Caps Heat Shrink Cable End Caps Heat Shrink End Caps Heat Shrink Cable End Caps Heat Shrink Products Parts Components |
| |
 |
| |
| Cable end sealing caps, heat shrink end caps, cable end sealing cap, bus bar insulation shrouds, heat shrinkable four way cable breakout, heat shrinkable right angle boot, heat shrink tube, cold shrink, cross linked polyolefin, insulation caps, end caps, rain sheds, cable termination kits ,heat shrinkable tubing,, dip moulding, Low voltage breakout, Cable Accessories, India |
| |
| Cable End Sealing Caps are : |
| |
- Suitable for Power Cables, Telecom Cables, Jelly Filled Cables & Optic Fibre Cable Compatible with most commonly used Cable Jackets i.e XLPE, PVC, PILC or Rubber Sheathed. Quick & foolproof installation using simple tools. A strong & permanent enviornmental seal. Excellent resistance to weathering, moisture contamination & adverse environmental conditions. Special adhesive lining provides seal on irregular cable sheaths.
|
- Valved end Cap available for pressurized applicatio
|
| |
 |
| |
SELECTION CHART |
All dimensions are in mm |
CODE NO. |
D MAX |
D MIN |
L |
T |
CABLE RANGE |
BEC 001 |
12 |
4 |
33 |
2.3 |
4 - 8 |
BEC 101 |
20 |
7.5 |
55 |
2.5 |
8 - 16 |
BEC 201 |
40 |
15 |
90 |
3.3 |
15 - 35 |
BEC 301 |
55 |
25 |
125 |
3.8 |
25 - 47 |
BEC 401 |
75 |
35 |
140 |
3.8 |
35 - 68 |
BEC 501 |
100 |
45 |
160 |
4.0 |
45 - 90 |
BEC 601 |
130 |
60 |
160 |
4.6 |
64 - 120 |
BEC 701 |
158 |
60 |
165 |
4.6 |
64 - 145 |
|
| |
| SPECIFICATION (As per ASTM STANDARDS) |
| |
| Heat Shrink Material |
: |
Cross Linked Polyolefin |
| Tensile Strength |
: |
12 N/mm² (MPA) |
| Elongation |
: |
350% |
| Density |
: |
1.20 gm/cm³ |
| Hardness |
: |
50 Shore D |
| Thermal Ageing |
: |
10% drop in physical properties |
| Water Absorption |
: |
<0.2% |
| Chemical Resistance |
: |
To dilute acids & alkalies, Salts etc. |
| Continuous Temperature limit |
: |
-40°C to 125°C |
| Shrink Temperature |
: |
125°C |
|
| |
| INSTALLATION PROCEDURE |
| |
 |
| |
-
Clean the cable surface & place the End Cap over the Cable End. On new cable, surface cleaning is not necessary. Heat the end seal with a kerosene or gas torch, starting from the closed end towards the open end.
-
When the end cap is fully shrunk the sealant will flow out the end cap indicating that the seal is completed. Allow to cool.
|
| |
Cable end sealing caps, heat shrink end caps, cable end sealing cap, bus bar insulation shrouds, heat shrinkable four way cable breakout, heat shrinkable right angle boot, heat shrink tube, cold shrink, cross linked polyolefin, insulation caps, end caps, rain sheds, cable termination kits ,heat shrinkable tubing,, dip moulding, Low voltage breakout, Cable Accessories, India. |
| |
 |
Related Words : Cable Sealing End Caps Pvc End Caps, Copper Screws , Pool Cover Anchors , Plastic Plumbing Fittings , Waterproof Electrical Connectors , Brass Hose Barbs , Brass Bolts , Brass Conduit Fittings , Brass Battery Terminals , Copper Rods , Brass Pipe Fittings , Brass Hose Fittings ,
Metric Fittings , Copper Tube Fittings , Brass Pipe , Brass Screws , Electric Connectors , Copper Pipe Fittings , Conduit Connectors , Brass Electrical Components , Brass Nuts , Brass Inserts , Tubing And Fittings , Copper Fitting , Electrical Fittings , Earthing Rods , Electrical Accessories ,
Cable Terminals , Electrical Wire Connectors , Terminal Ends , Battery Terminals , Cable Connectors , Metal Cable Connectors , Brass Fitting , Stainless Steel Fittings , Plumbing Fittings , Electric Connector , Electrical Wire , Brass Nut , Brass Fasteners , Electrical Connections , Brass Components ,
|
|
|
| |
Please enquire here for Cable Sealing End Caps Pvc End Caps manufacturers exporters suppliers India China Jamnagar |
|
|
|
| |
|
